NetBSD/acs6k
Avocent ACS6008 への移植。
これは PowerPC 440。
<![CDATA[
U-Boot 1.2.0. AVCT-Boot 2.0.2.3 (Sep 8 2011 - 09:50:11)
CPU: AMCC PowerPC 440EPx Rev. A at 533.333 MHz (PLB=133, OPB=66, EBC=66 MHz)
Security/Kasumi support
I2C boot EEPROM disabled
Bootstrap Option A - Boot ROM Location EBC (8 bits)
Internal PCI arbiter disabled, PCI async ext clock used
32 kB I-Cache 32 kB D-Cache
ACS6000 Board, serial# 0520050205
I2C: ready
DTT: 1 is 26 C
DRAM: 256 MB
FLASH: 512 kB
NAND: 128 MiB
PCI: Bus Dev VenId DevId Class Int
00 0a 104c ac55 0607 ff
00 0a 104c ac55 0607 ff
In: serial
Out: serial
Err: serial
USB: Host(int phy) Device(ext phy)
Watchdog enabled
Net: ppc_4xx_eth0, ppc_4xx_eth1
Hit any key to stop autoboot: 0
Booting from network ...
Trying ppc_4xx_eth0
Waiting for PHY auto negotiation to complete.... done
ENET Speed is 1000 Mbps - FULL duplex connection
Using ppc_4xx_eth0 device
TFTP from server 10.9.2.2; our IP address is 10.9.2.34
Filename 'boot.acs6k'.
Load address: 0x1000000
Loading: #####
done
Bytes transferred = 25537 (63c1 hex)
## Booting image at 01000000 ...
Kernel from 00000040 (25473 bytes).
Uncompressing Kernel Image ... OK.
## cmdline at 0x007FFF00 ... 0x007FFF25
memstart = 0x00000000
memsize = 0x10000000
flashstart = 0xFFF80000
flashsize = 0x00080000
flashoffset = 0x00000000
sramstart = 0x00000000
sramsize = 0x00000000
bootflags = 0x00000000
procfreq = 533.333 MHz
plb_busfreq = 133.333 MHz
pci_busfreq = 0 MHz
ethaddr = 00:E0:86:19:01:26
eth1addr = 00:E0:86:19:01:27
IP addr = 10.9.2.34
baudrate = 57600 bps
>> NetBSD/acs6k ACS6000 Boot, Revision 1.1
>> (tsubai@sakura, Sun Jan 22 15:05:15 JST 2017)
ENET Speed is 1000 Mbps - FULL duplex connection
Using IP address: 10.9.2.34
root addr=10.9.2.2 path=/e/ppc
2551092+89380 [165264+148701]=0x2d1908
start=0x100000
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 6.99.23 (ACS6K) #257: Thu Jan 26 21:33:28 JST 2017
tsubai@sakura:/sys/arch/acs6k/compile/ACS6K
total memory = 256 MB
avail memory = 247 MB
mainbus0 (root)
cpu0 at mainbus0: 440EPx (Revision 18d0), ID 0 (primary)
cpu0: CCR0 0x206000<DSTG,GICBT,GDCBT>
plb0 at mainbus0
com0 at plb0 offset 0x300 irq 0: ns16550a, working fifo
com0: console
com1 at plb0 offset 0x400 irq 1: ns16550a, working fifo
emac0 at plb0 offset 0xe00 irq 70,72: address 00:e0:86:19:01:26
ukphy0 at emac0 phy 1: Marvell 88E1121 Gigabit PHY, rev. 3
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
emac1 at plb0 offset 0xf00 irq 71,73: address 00:e0:86:19:01:27
ukphy1 at emac1 phy 0: Marvell 88E1121 Gigabit PHY, rev. 3
ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
i2c0 at plb0 offset 0x700
i2c1 at plb0 offset 0x800
ohci0 at plb0: irq 21
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
ehci0 at plb0: irq 26
ehci0: companion controller, 1 port each: ohci0
usb1 at ehci0: USB revision 2.0
pci0 at plb0 bus 0
pchb0 at pci0 dev 0 function 0
pchb0: IBM product 0x027f (rev. 0x00)
cbb0 at pci0 dev 10 function 0: Texas Instruments PCI1520 PCI-CardBus Bridge (rev. 0x01)
cbb1 at pci0 dev 10 function 1: Texas Instruments PCI1520 PCI-CardBus Bridge (rev. 0x01)
cbb0: interrupting at irq 62
cardslot0 at cbb0
cardbus0 at cardslot0: bus 1
pcmcia0 at cardslot0
cbb1: interrupting at irq 67
cardslot1 at cbb1
cardbus1 at cardslot1: bus 2
pcmcia1 at cardslot1
ndfc0 at plb0
nand0 at ndfc0: ONFI NAND Flash
nand0: vendor: ST, model: NAND01GW3B2CN6
nand0: page size: 2048 bytes, spare size: 64 bytes, block size: 131072 bytes
nand0: LUN size: 1024 blocks, LUNs: 1, total storage size: 128 MB
nand0: column cycles: 2, row cycles: 2, width: x8
flash0 at nand0: NAND flash partition size 128 MB, offset 0
flash0: erase size 128 KB, page size 2048 bytes, write size 2048 bytes
obio0 at mainbus0: FPGA 2.0, 2 PSUs, AUX
hwmon0 at obio0
com2 at obio0 offset 0x8000000 irq 65: xr16v798, working fifo
com3 at obio0 offset 0x8000010 irq 65: xr16v798, working fifo
com4 at obio0 offset 0x8000020 irq 65: xr16v798, working fifo
com5 at obio0 offset 0x8000030 irq 65: xr16v798, working fifo
com6 at obio0 offset 0x8000040 irq 65: xr16v798, working fifo
com7 at obio0 offset 0x8000050 irq 65: xr16v798, working fifo
com8 at obio0 offset 0x8000060 irq 65: xr16v798, working fifo
com9 at obio0 offset 0x8000070 irq 65: xr16v798, working fifo
uhub0 at usb0: PPC440 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1 at usb1: PPC440 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
boot device: emac0
root on emac0
nfs_boot: trying DHCP/BOOTP
nfs_boot: DHCP next-server: 10.9.2.2
nfs_boot: my_name=acs6008
nfs_boot: my_addr=10.9.2.34
nfs_boot: my_mask=255.255.255.0
nfs_boot: gateway=10.9.2.2
root on sakura:/e/ppc
root file system type: nfs
Enter pathname of shell or RETURN for /bin/sh:
#
#
#
]]></plaintext></p></body></div>