NetBSD/c181x
Cisco 1812J で NetBSD を動かしました。
SC8517 という謎の CPU が載っています。400MHz の e500v1 なのはわかるけど。
BUFFALO AN266-A512M という SO-DIMM モジュールをさしています。
DDR266 だけどとりあえず使えてるみたい。
<![CDATA[
System Bootstrap, Version 12.3(8r)YH8, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2006 by cisco Systems, Inc.
C1800 platform with 655360 Kbytes of main memory with parity disabled
Upgrade ROMMON initialized
rommon 1 > boot
program load complete, entry point: 0x80012000, size: 0xc0c0
Initializing ATA monitor library.......
program load complete, entry point: 0x80012000, size: 0xc0c0
Initializing ATA monitor library.......
program load complete, entry point: 0x80012000, size: 0xac88
>> NetBSD/c181x Cisco181x Boot, Revision 1.1
>> (tsubai@sakura, Sun Nov 27 22:01:29 JST 2011)
Using IP address: 10.9.2.18
root addr=10.9.2.2 path=/e/e500
2002508+69044 [131792+123820]=0x2386fc
start=0x100000
ssym=0x2f9c00 esym=0x3386fc
physload 0x00341000 - 0x28000000
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009, 2010, 2011
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 5.99.56 (C1812J) #58: Sun Dec 18 07:53:34 JST 2011
tsubai@sakura:/a/1101/src/sys/arch/c181x/compile/C1812J
total memory = 640 MB
avail memory = 624 MB
mainbus0 (root)
cpu0 at mainbus0: SC8517 (Revision 11), ID 0 (primary)
cpu0: HID0 0x80804000<EMCP,DOZE,TBEN>
cpu0: HID1 0x44021000<PM1,PC3,RFXE,ABE>
cpu0: 256KB L2 cache
flash0 at mainbus0: 29LV160 (2MB)
lb0 at mainbus0
com0 at lb0 addr 0x4500 irq 42: ns16550a, working fifo
com0: console
com1 at lb0 addr 0x4600 irq 42: ns16550a, working fifo
tsec0 at lb0 addr 0x24000 irq 29,30: address 00:18:18:d1:da:6e
ukphy0 at tsec0 phy 8: OUI 0x0010a1, model 0x0021, rev. 9
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
tsec1 at lb0 addr 0x25000 irq 35,36: address 00:18:18:d1:da:6f
ukphy1 at tsec1 phy 9: OUI 0x0010a1, model 0x0021, rev. 9
ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pbi0 at lb0: addr 0x8000
pci0 at pbi0 bus 0
pci0: memory space enabled
pchb0 at pci0 dev 0 function 0
pchb0: Motorola SC8517 Host Bridge (rev. 0x11)
ohci0 at pci0 dev 16 function 0: Philips ISP1561 USB Host Controller (rev. 0x30)
ohci0: interrupting at irq 4
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
ohci1 at pci0 dev 16 function 1: Philips ISP1561 USB Host Controller (rev. 0x30)
ohci1: interrupting at irq 4
ohci1: OHCI version 1.0
usb1 at ohci1: USB revision 1.0
ehci0 at pci0 dev 16 function 2: Philips ISP1561 USB Host Controller (rev. 0x30)
ehci0: interrupting at irq 4
ehci0: EHCI version 0.95
ehci0: companion controllers, 1 port each: ohci0 ohci1
usb2 at ehci0: USB revision 2.0
uhub0 at usb0: Philips OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 1 port with 1 removable, self powered
uhub1 at usb1: Philips OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 1 port with 1 removable, self powered
uhub2 at usb2: Philips EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
umass0 at uhub2 port 1 configuration 1 interface 0
umass0: Silicon Integrated Systems USB Mass Storage Device, rev 2.00/1.00, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
sd0 at scsibus0 target 0 lun 0: <PACCOM, USB Flash Disk, 0.00> disk removable
sd0: 242 MB, 500 cyl, 8 head, 32 sec, 512 bytes/sect x 496000 sectors
boot device: tsec0
root on tsec0
nfs_boot: trying DHCP/BOOTP
nfs_boot: DHCP next-server: 10.9.2.2
nfs_boot: my_name=cisco1812
nfs_boot: my_addr=10.9.2.18
nfs_boot: my_mask=255.255.255.0
nfs_boot: gateway=10.9.2.2
root on sakura:/e/e500
root file system type: nfs
WARNING: no TOD clock present
enabling watchdog tick
Enter pathname of shell or RETURN for /bin/sh:
# pwd
/
#
]]></plaintext></p></body></div>