NetBSD/n1200
Thecus N1200 と N3200 で NetBSD を動かしてみました。
まだ一部(どころかいろいろと)ちゃんと動いていません。
マルチユーザーで動いて slogin したりはできます。
ちなみに bcベンチ:-) は 40秒ほどです(N1200)。
ソースコードとカーネルをいつものところに置きました。
<![CDATA[
U-Boot 1.1.3 (FSL Development) (Jan 31 2007 - 17:57:16) MPC83XX
Clock configuration:
Coherent System Bus: 266 MHz
Core: 266 MHz
Local Bus Controller: 266 MHz
Local Bus: 33 MHz
DDR: 266 MHz
I2C: 266 MHz
TSEC1: 266 MHz
TSEC2: 266 MHz
USB MPH: 88 MHz
USB DR: 88 MHz
CPU: MPC83xx, Rev: 11 at 266.666 MHz
Board: Thecus N1200
I2C: ready
DRAM: SDRAM on Local Bus is NOT available!
DDR RAM: 128 MB
FLASH: 8 MB
PCI1 32bit on PMC1 & PMC2 & PMC3
In: serial
Out: serial
Err: serial
Net: Freescale TSEC0: PHY is Realtek RTL8211B (1cc912)
Freescale TSEC1: PHY id 1410c87 is not supported!
Freescale TSEC1: No PHY found
Freescale TSEC0, Freescale TSEC1
Thecus Version: 3, PIC version: 4
Hit any key to stop autoboot: 0
=> boot
Speed: 100, full duplex
BOOTP broadcast 1
Using Freescale TSEC0 device
TFTP from server 10.1.1.1; our IP address is 10.1.1.12
Filename 'boot.n1200'.
Load address: 0x8000
Loading: #########
done
Bytes transferred = 43140 (a884 hex)
## Booting image at 00008000 ...
Image Name: Boot
Image Type: PowerPC NetBSD Kernel Image (uncompressed)
Data Size: 43076 Bytes = 42.1 kB
Load Address: 00004000
Entry Point: 00004000
Verifying Checksum ... OK
OK
## Transferring control to NetBSD stage-2 loader (at address 00004000) ...
>> NetBSD/n1200 Boot, Revision 1.1
>> (tsubai@sakura, Wed Dec 31 15:17:15 JST 2008)
2284472+229408 [144640+137813]=0x2aaefc
start=0x100000
bootpath: disk:/netbsd
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 5.99.7 (N1200) #1: Sun Mar 15 02:18:38 JST 2009
tsubai@sakura:/a/0301/src/sys/arch/n1200/compile/N1200
total memory = 128 MB
avail memory = 121 MB
mainbus0 (root)
cpu0 at mainbus0: 8347 (Revision 11), ID 0 (primary)
cpu0: HID0 0x8090c000<EMCP,DOZE,DPM,ICE,DCE>
cpu0: HID1 0x44000000<PC1,PC5>
cpu0: HID2 0xe40000<IFEC,EBQS,EBPX,HBE>
flash0 at mainbus0: 28F640 (8MB)
lb0 at mainbus0
com0 at lb0 addr 0x4500 irq 9: ns16550a, working fifo
com0: console
com1 at lb0 addr 0x4600 irq 10: ns16550a, working fifo
tsec0 at lb0 addr 0x24000 irq 32,33: address 00:14:fd:10:93:d2
rgephy0 at tsec0 phy 17: RTL8169S/8110S/8211 1000BASE-T media interface, rev. 2
rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
tsec1 at lb0 addr 0x25000 irq 35,36: address 00:14:fd:10:93:d3
mvphy0 at tsec1 phy 1: Marvell 88E6060 10/100 5-port PHY switch, rev. 7
mvphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
mvphy1 at tsec1 phy 2: Marvell 88E6060 10/100 5-port PHY switch, rev. 7
mvphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
mvphy2 at tsec1 phy 3: Marvell 88E6060 10/100 5-port PHY switch, rev. 7
mvphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
mvphy3 at tsec1 phy 4: Marvell 88E6060 10/100 5-port PHY switch, rev. 7
mvphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ehci0 at lb0: addr 0x22100 irq 39
ehci0: EHCI version 1.0
usb0 at ehci0: USB revision 2.0
i2c0 at lb0 addr 0x3000
i2c1 at lb0 addr 0x3100
pbi0 at lb0: addr 0x8300
pci0 at pbi0 bus 0
pci0: i/o space, memory space enabled
pchb0 at pci0 dev 0 function 0
pchb0: unknown vendor 0x1957 product 0x0085 (rev. 0x11)
pcic0 at pci0 dev 15 function 0: TI PCI1410 PCMCIA controller
pcic0: controller 0 (Intel 82365SL Revision 0) has sockets A and B
pcic0: interrupting at irq 21
pcmcia0 at pcic0 controller 0 socket 0
pcic0: WARNING: powerhook_establish is deprecated
satalink0 at pci0 dev 16 function 0: Silicon Image SATALink 3512 (rev. 0x01)
satalink0: SATALink BA5 register space disabled
satalink0: bus-master DMA support present
satalink0: using irq 20 for native-PCI interrupt
atabus0 at satalink0 channel 0
atabus1 at satalink0 channel 1
pbi1 at lb0: addr 0x8380
pci1 at pbi1 bus 0
pci1: i/o space, memory space enabled
pchb1 at pci1 dev 0 function 0
pchb1: unknown vendor 0x1957 product 0x0085 (rev. 0x11)
obio0 at mainbus0
rsclock0 at obio0 addr 0x64: 5C372 RTC
tio0 at obio0 addr 0x6c: Thecus I/O
fan0 at obio0 addr 0x5c: F75375S
satalink0: port 0: device present, speed: 1.5Gb/s
wd0 at atabus0 drive 0: <ST380013AS>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 19077 MB, 38760 cyl, 16 head, 63 sec, 512 bytes/sect x 39070080 sectors
uhub0 at usb0: MPC8347 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(satalink0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
wi0 at pcmcia0 function 0: <Lucent Technologies, WaveLAN/IEEE, Version 01.01, >
pcic0: port 0x2000-0x203f
wi0: 802.11 address 00:02:2d:5b:b4:90
wi0: using Lucent Embedded WaveLAN/IEEE
wi0: Lucent Firmware: Station (6.16.1)
wi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
Automatic boot in progress: starting file system checks.
...
U-Boot 1.1.6 (Sep 28 2007 - 13:46:00) MPC83XX
Clock configuration:
Coherent System Bus: 266 MHz
Core: 399 MHz
Local Bus Controller: 266 MHz
Local Bus: 66 MHz
DDR: 266 MHz
SEC: 88 MHz
I2C1: 266 MHz
I2C2: 266 MHz
TSEC1: 266 MHz
TSEC2: 266 MHz
USB MPH: 88 MHz
USB DR: 88 MHz
CPU: MPC8347, Rev: 31 at 399.999 MHz
Board: Thecus N3200
I2C: ready
DRAM: Initializing
DDR DIMM: data bus width is 64 bit without ECC
DDRC ECC mode: OFF
DDR RAM: 256 MB
FLASH: 16 MB
PCI1: 32-bit on PMC1, PMC2, PMC3
PCI1: 66.67 MHz
In: serial
Out: serial
Err: serial
Net: TSEC0, TSEC1
Thecus Version: 6, PIC version: 012
Hit any key to stop autoboot: 0
N3200 => setenv bootargs disk1:
N3200 => bootm fe640000
## Booting image at fe640000 ...
Image Name: Boot
Created: 1970-01-01 0:00:00 UTC
Image Type: PowerPC NetBSD Kernel Image (uncompressed)
Data Size: 43608 Bytes = 42.6 kB
Load Address: 00004000
Entry Point: 00004000
Verifying Checksum ... OK
OK
## Transferring control to NetBSD stage-2 loader (at address 00004000) ...
>> NetBSD/n1200 Boot, Revision 1.1
>> (tsubai@sakura, Mon Jan 12 11:17:34 JST 2009)
2284408+229392 [144416+137560]=0x2aaccc
start=0x100000
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 5.99.5 (N3200) #30: Mon Jan 12 11:22:56 JST 2009
tsubai@sakura:/a/0101/src/sys/arch/n1200/compile/N3200
total memory = 256 MB
avail memory = 246 MB
mainbus0 (root)
cpu0 at mainbus0: 8347 (Revision 30), ID 0 (primary)
cpu0: HID0 0x8090c000<EMCP,DOZE,DPM,ICE,DCE>
cpu0: HID1 0x46000000<PC1,PC5,PC6>
cpu0: HID2 0xe40000<IFEC,EBQS,EBPX,HBE>
lb0 at mainbus0
com0 at lb0 addr 0x4500 irq 9: ns16550a, working fifo
com0: console
com1 at lb0 addr 0x4600 irq 10: ns16550a, working fifo
tsec0 at lb0 addr 0x24000 irq 32,33: address 00:14:fd:11:b5:a6
rgephy0 at tsec0 phy 17: RTL8169S/8110S/8211 1000BASE-T media interface, rev. 2
rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
tsec1 at lb0 addr 0x25000 irq 35,36: address 00:14:fd:11:b5:a7
rgephy1 at tsec1 phy 1: RTL8169S/8110S/8211 1000BASE-T media interface, rev. 2
rgephy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
ehci0 at lb0: addr 0x22100 irq 39
ehci0: EHCI version 1.0
usb0 at ehci0: USB revision 2.0
i2c0 at lb0 addr 0x3000
i2c1 at lb0 addr 0x3100
pbi0 at lb0: addr 0x8300
pci0 at pbi0 bus 0
pci0: i/o space, memory space enabled
pchb0 at pci0 dev 0 function 0
pchb0: unknown vendor 0x1957 product 0x0085 (rev. 0x30)
satalink0 at pci0 dev 16 function 0: Silicon Image SATALink 3114 (rev. 0x02)
satalink0: 66MHz PCI bus
satalink0: bus-master DMA support present
satalink0: using irq 20 for native-PCI interrupt
atabus0 at satalink0 channel 0
atabus1 at satalink0 channel 1
atabus2 at satalink0 channel 2
atabus3 at satalink0 channel 3
pbi1 at lb0: addr 0x8380
pci1 at pbi1 bus 0
pci1: memory space enabled
pchb1 at pci1 dev 0 function 0
pchb1: unknown vendor 0x1957 product 0x0085 (rev. 0x30)
obio0 at mainbus0
rsclock0 at obio0 addr 0x164: 5C372 RTC
tio0 at obio0 addr 0x6c: Thecus I/O
fan0 at obio0 addr 0x15c: F75375S
satalink0: port 1: device present, speed: 1.5Gb/s
wd0 at atabus1 drive 0: <ST380013AS>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 76319 MB, 155061 cyl, 16 head, 63 sec, 512 bytes/sect x 156301488 sectors
uhub0 at usb0: MPC8347 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(satalink0:1:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
umass0 at uhub0 port 1 configuration 1 interface 0
umass0: Silicon Integrated Systems USB Mass Storage Device, rev 2.00/1.00, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
sd0 at scsibus0 target 0 lun 0: <PACCOM, USB Flash Disk, 0.00> disk removable
sd0: 242 MB, 500 cyl, 8 head, 32 sec, 512 bytes/sect x 496000 sectors
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
Automatic boot in progress: starting file system checks.
...
]]></plaintext></p></body></div>